Sockets, Switches & Accessories (1618)

Flush-mounted rotary dimmer, LED dimmer insert, switchable between leading-edge and trailing-edge control via selector switch. With rotary operation, two-way push-sequence switch, and soft-detent. 2-wire connection technology (neutral conductor not required). Optimized for dimming retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi) on conventional or electronic transformers. For incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Mixed load operation of LEDi and conventional lamps possible. Switchable between leading-edge and trailing-edge control via selector switch. Quiet operation due to the use of MOSFET transistors. Short-circuit-proof and overload-protected (electronic fuse). With adjustable minimum brightness. Without center plate. Nominal voltage: 230 V~, + 10% / - 10% Consisting of: LED dimmer, dimmer cover plate, and single frame - Dimmer and cover plate in Busch-Jaeger design: Reflex SI Alpine white glossy LED rotary dimmer type: 6523 U-102 Minimum and maximum brightness - Leading-edge or trailing-edge control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Assembled and ready for installation for you by the cable professionals at EBROM, including EBROM phase tester for mounting the device Manufacturer of LED dimmer, dimmer cover plate, and single frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

Flush-mounted rotary dimmer, LED dimmer insert, switchable between leading-edge and trailing-edge control via selector switch. With rotary operation, push-button changeover switch, and soft-detent. 2-wire connection technology (neutral conductor not required). Optimized for dimming retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi) on conventional or electronic transformers. For incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Mixed load operation of LEDi and conventional lamps possible. Switchable between leading-edge and trailing-edge control via selector switch. Low-noise due to the use of MOSFET transistors. Short-circuit proof and overload-protected (electronic fuse). With adjustable minimum brightness. Without center plate. Nominal voltage: 230 V~, + 10 % / - 10 % Consisting of: LED dimmer and dimmer knob (simply install this dimmer with center plate in existing 1, 2, 3, 4 or 5-gang frames in your home and use as a replacement or extension for standard light switches or similar, dimmer and knob in Busch-Jaeger design: Reflex SI alpine white glossy LED rotary dimmer type: 6523 U-102 Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - including glow lamp (dimmer ring is illuminated when "OFF") Ready-to-install set assembled for you by the cable professionals at EBROM, including EBROM voltage tester for mounting the device Manufacturer of LED dimmer and dimmer knob: Busch-Jaeger // Manufacturer of voltage tester: EBROM; A SET IDEA BY EBROM

Flush-mounted rotary dimmer, LED dimmer insert, switchable between leading-edge and trailing-edge control via selector switch. With rotary control, push-action change-over switch and soft-click mechanism. 2-wire connection technology (neutral conductor not required). Optimized for dimming retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi). For dimmable retrofit LED lamps (LEDi) on conventional or electronic transformers. For incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Mixed load operation of LEDi and conventional lamps possible. Switchable between leading-edge and trailing-edge control via selector switch. Quiet operation due to the use of MOSFET transistors. Short-circuit proof and overload-protected (electronic fuse). With adjustable minimum brightness. Without central plate. Nominal voltage: 230 V~, + 10 % / - 10 % Consisting of: LED dimmer, dimmer knob and single frame - Dimmer and knob in Busch-Jaeger design: Reflex SI alpine white glossy LED rotary dimmer type: 6523 U-102 Minimum and maximum brightness - Leading-edge or trailing-edge phase control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Pre-assembled for you by the cable professionals at EBROM, including an EBROM phase tester for installation of the device Manufacturer of LED dimmer, dimmer knob and single frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require a claw-fixing mechanism. It features rotary operation, a push-changeover switch, and soft-locking. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), including those operated on conventional as well as electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge control, as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the center plate. When using conventional transformers, approximately 20% transformer loss should be taken into account, and approximately 5% for electronic transformers. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with EU Directive RoHS 3 of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: 2 x LED dimmer, 2 x dimmer dial, socket, and triple frame - The system is in the Busch Jäger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and requires no claw-fixing. With its rotary and push operation, it is easy to use and does not require a neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge adjustable - Includes glow lamp (the ring of the dimmer is illuminated when "OFF") Ready-to-install, assembled for you by the cable professionals at EBROM, including an EBROM phase tester for installing the devices - This combination can be mounted both horizontally and vertically; the photo is for illustration of horizontal mounting Manufacturer of LED dimmer, dimmer dials, socket, and 3-gang frame: Busch Jäger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and soft-click detents. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), both for those operated on conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional lamps. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included in the scope of delivery of the central plate. When used with conventional transformers, approximately 20% transformer losses should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 VA. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: 2x LED dimmer, 2x dimmer knob, cross switch (for intermediate switching), rocker, and triple frame - The system is in the Busch-Jaeger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of under 20 mm and does not require expansion claws. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power rating of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - Includes glow lamp (the ring of the dimmer is illuminated when "OFF") Assembled ready for installation for you by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate horizontal mounting Manufacturer of LED dimmer, dimmer knobs, cross switch, cross switch rocker, and triple frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features a rotary control, a push-button changeover switch, and soft-click detents. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), whether operated with conventional or electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Additionally, it supports mixed-load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge control, as well as adjustable minimum and maximum brightness levels. It operates quietly thanks to the use of MOSFET transistors and is short-circuit and overload-protected via an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer loss should be taken into account, and approximately 5% for electronic transformers. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer complies with the EU Directive RoHS 3 of July 22, 2019, and has an IP20 protection rating. The ambient operating temperature is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: 2 x LED dimmer, 2 x dimmer dial, light switch (two-way ON/OFF switch), rocker, and triple frame - The system is in the Busch-Jaeger design: Reflex SI alpine white glossy The type 6523 UR-104 LED rotary dimmer has an installation depth of less than 20 mm and requires no expansion. With its rotary and push-button operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and a nominal power of 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - Leading-edge or trailing-edge phase control adjustable - Includes glow lamp (the ring of the dimmer is illuminated when "OFF") Assembled ready for installation by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted either horizontally or vertically; the photo serves to illustrate horizontal mounting Manufacturer of LED dimmer, dimmer dials, switches, switch rockers, and triple frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and soft-detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), whether operated with conventional or electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional lamps. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included in the scope of delivery of the central plate. When used with conventional transformers, approximately 20% transformer losses should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer complies with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: 2 pieces LED dimmer, 2 x dimmer dial, light push-button (push-button with spring mechanism) remains in its original position after actuation - rocker and triple frame - The system is in the Busch-Jaeger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require expansion. With its rotary and push operation, it is easy to use and does not require a neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Assembled ready for installation for you by the cable professionals at EBROM, including EBROM voltage tester for mounting the devices - This combination can be mounted both horizontally and vertically, the photo serves to illustrate the horizontal installation Manufacturer of LED dimmer, dimmer dials, push-button, push-button rocker and 3-gang frame: Busch-Jaeger // Manufacturer of voltage tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion claw mechanism. It features a rotary control, a push-changeover switch, and a soft-click detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), both for those operated with conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control as well as adjustable minimum and maximum brightness. By using MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, about 20% transformer losses should be taken into account; for electronic transformers, about 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with the EU RoHS 3 directive dated July 22, 2019, and has an IP20 degree of protection. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: 2 x LED dimmer, 2 x dimmer dial, socket with child protection, and triple frame - The system is in the Busch Jäger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and requires no expansion. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - Includes glow lamp (ring of the dimmer is illuminated when "OFF") Ready for installation and assembled for you by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo is for the purpose of illustrating horizontal mounting Manufacturer of LED dimmer, dimmer dials, socket with child protection, and 3-gang frame: Busch Jäger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer features a shallow installation depth of less than 20 mm and does not require a spreading mechanism. It is equipped with a rotary control, a push-sequence changeover switch, and a soft-click detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), including those operated with conventional or electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional light sources. For individual customization, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge control, as well as adjustable minimum and maximum brightness. By using MOSFET transistors, it operates quietly. It is short-circuit proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer loss should be taken into account, and approximately 5% for electronic transformers. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power rating of 2 to 400 V·A. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient operating temperature is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer knob, cross switch (for cross-switching), rocker, socket, and triple frame - The system is in the design of Busch-Jaeger: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require spreading. With its rotary and push operation, it is easy to use and does not require a neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - Leading-edge or trailing-edge phase control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Ready for installation, put together for you by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo is for the purpose of illustrating horizontal mounting Manufacturer of LED dimmer, dimmer knob, socket, cross switch, cross switch rocker, and triple frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its low installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and soft-detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), both for those operated on conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, as well as dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer losses should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer dial, light switch (changeover switch ON/OFF), rocker, socket, and triple frame - The system is in the design of Busch-Jaeger: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require spreading claws. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit proof as well as overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - includes glow lamp (dimmer ring is illuminated when "OFF") Ready for installation and assembled for you by the cable professionals at EBROM, including EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate the horizontal installation Manufacturer of LED dimmer, dimmer dial, socket, switch, switch rocker, and triple frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and a soft-click detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), both for those operated on conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, as well as dimmable halogen energy-saving lamps. In addition, it supports mixed-load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control, as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When using conventional transformers, transformer losses of approximately 20% should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer complies with the EU Directive RoHS 3 of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer plate, light button (push-button with spring mechanism) - remains in its original position after actuation - rocker, socket, and triple frame - The system is in the design of Busch-Jaeger: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require expansion. With its rotary and push operation, it is easy to use and does not require a neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and a nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - Includes glow lamp (ring of the dimmer is illuminated when "OFF") Ready for installation and assembled for you by the cable professionals at EBROM, including EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate the horizontal installation Manufacturer of LED dimmer, dimmer plate, socket, push-button, button rocker, and triple frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and a soft-click detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), including those operated on conventional or electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Additionally, it supports mixed load operation with LEDi and conventional light sources. For individual customization, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control, as well as adjustable minimum and maximum brightness. By using MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a rated voltage of 230 V~ (+/- 10%), a rated frequency of 50/60 Hz, and a rated output of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer loss should be taken into account, or approximately 5% for electronic transformers. Additional details include a rated voltage range of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with EU Directive RoHS 3 of July 22, 2019, and has an IP20 protection rating. The ambient operating temperature is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer dial, intermediate switch (for intermediate circuit), rocker, and double frame - The system is in the Busch Jäger Reflex SI alpine white glossy design The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and requires no spreader. With its rotary and push operation, it is easy to use and does not require a neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit and overload-proof. The rated voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and rated power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Ready for installation and assembled for you by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate horizontal mounting Manufacturer of LED dimmer, dimmer dial, intermediate switch, intermediate switch rocker, and double frame: Busch Jäger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer features a shallow installation depth of less than 20 mm and does not require an expansion mechanism. It is equipped with rotary operation, a push-changeover switch, and a soft-click detent. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specifically optimized for dimming retrofit LED lamps (LEDi), both those operated with conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. Additionally, it supports mixed load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control, as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When using conventional transformers, approx. 20% transformer loss should be taken into account, and approx. 5% for electronic transformers. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient temperature for operation is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer knob, light switch (two-way switch ON/OFF), rocker, and double frame - The system is in the Busch Jäger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require expansion. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof as well as overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - Leading-edge or trailing-edge phase control adjustable - Includes glow lamp (dimmer ring is illuminated when "OFF") Ready for installation and assembled for you by the cable professionals at EBROM, includes EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate horizontal mounting Manufacturer of LED dimmer, dimmer knob, switch, switch rocker, and double frame: Busch Jäger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and soft-click detents. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), including those operated with conventional or electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional light sources. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge phase control, as well as adjustable minimum and maximum brightness. By using MOSFET transistors, it operates quietly. It is short-circuit-proof and overload-protected thanks to an electronic fuse. Technical specifications include a rated voltage of 230 V~ (+/- 10%), a rated frequency of 50/60 Hz, and a rated power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer losses should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 VA. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has an IP20 protection rating. The ambient operating temperature is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer dial, light switch (button with spring mechanism - returns to its original position after actuation), rocker, and double frame - The system is in the Busch-Jaeger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and does not require expansion claws. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit-proof and overload-protected. The rated voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and rated power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - leading-edge or trailing-edge phase control adjustable - includes glow lamp (dimmer ring is illuminated when "OFF") Ready for installation, assembled for you by the cable professionals at EBROM, including an EBROM phase tester for installing the devices - This combination can be mounted both horizontally and vertically; the photo is for illustration of horizontal mounting Manufacturer of LED dimmer, dimmer dial, push-button, rocker, and double frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

This compact dimmer is characterized by its shallow installation depth of less than 20 mm and does not require an expansion mechanism. It features rotary operation, a push-changeover switch, and soft-detent mechanism. Thanks to the 2-wire connection technology, no neutral conductor is required. The dimmer is specially optimized for dimming retrofit LED lamps (LEDi), both for those operated on conventional and electronic transformers. It is also suitable for incandescent lamps, 230 V halogen lamps, low-voltage halogen lamps with conventional or electronic transformers, and dimmable halogen energy-saving lamps. In addition, it supports mixed load operation with LEDi and conventional lamps. For individual adjustment, the dimmer offers manually adjustable operating modes for leading-edge and trailing-edge control as well as adjustable minimum and maximum brightness. Due to the use of MOSFET transistors, it operates quietly. It is short-circuit proof and overload-protected thanks to an electronic fuse. Technical specifications include a nominal voltage of 230 V~ (+/- 10%), a nominal frequency of 50/60 Hz, and a nominal power of 2 - 100 W/VA (leading-edge) or 2 - 400 W/VA (trailing-edge). The dimmer can be illuminated by a glow lamp, which is included with the central plate. When used with conventional transformers, approximately 20% transformer losses should be taken into account; for electronic transformers, approximately 5%. Additional details include a rated voltage of 207 to 253 V, a rated control supply voltage of 220 to 240 V, a frequency of 50 to 60 Hz, and a power of 2 to 400 V·A. The dimmer is compliant with the EU RoHS 3 directive of July 22, 2019, and has a protection rating of IP20. The ambient operating temperature is between 0 and +35 °C. Dimensions: WxHxD 71mm x 71mm x 42mm, installation depth 20 mm Consisting of: LED dimmer, dimmer plate, socket, and double frame - The system features a Busch-Jaeger design: Reflex SI alpine white glossy The LED rotary dimmer type 6523 UR-104 has an installation depth of less than 20 mm and requires no expansion. With its rotary and push operation, it is easy to use and requires no neutral conductor. It is optimized for retrofit LEDs and compatible with various lamp types, supports mixed operation, and is short-circuit proof and overload-protected. The nominal voltage is 230 V~ (+/- 10%) with a power of 2 - 100 W/VA (leading-edge) and nominal power: 2 - 400 W/VA (trailing-edge) Minimum and maximum brightness - Leading-edge or trailing-edge control adjustable - Includes glow lamp (the ring of the dimmer is illuminated when "OFF") Ready for installation, assembled for you by the cable professionals at EBROM, including an EBROM phase tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate the horizontal installation Manufacturer of LED dimmer, dimmer plate, socket, and 2-gang frame: Busch-Jaeger // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM