Sockets, Switches & Accessories (1618)

EBROM LED DIMMER UNIVERSAL PRO 1002, suitable for dimmable LED lamps, dimmable LED drivers, incandescent lamps, HV and LV halogen lamps with electronic transformer. Freely selectable dimming principle setting (leading-edge or trailing-edge), manually switchable, simple adjustment of min. and max. brightness as an optimization option for flicker-free dimming, automatic neutral conductor detection, 2- or 3-wire connection possible, electronic short-circuit and overload protection and overtemperature protection with automatic reactivation, no stand-by consumption due to a real on/off switch Consisting of: 3 pieces EBROM LED DIMMER TYPE 1002, 3 x Busch Jäger dimmer dial and triple frame - Dimmer and dials in the design of Busch Jäger: BalanceSi alpine white glossy EBROM flush-mounted LED dimmer UNIVERSAL PRO 1002 - trailing-edge and leading-edge dimmer. From 3 to 150 watts (e.g. also multiple 3.5 watt LEDs in one lamp) as well as for incandescent, HV and LV halogen lamps with electronic transformer from 10 to 400 W - Absolutely silent operation, no humming or buzzing, dimensions: 71 x 71 x 33 mm, 230 V~, 50 Hz nominal voltage Important: please check before purchase whether the light source and/or transformer are dimmable. We recommend light sources from well-known manufacturers. Manually switchable, simple adjustment of min. and max. brightness as an optimization option for flicker-free dimming, automatic neutral conductor detection, 2- or 3-wire connection possible. Extremely high compatibility of over 99% of all dimmable light sources available on the market Ready for installation and assembled for you by the cable professionals at EBROM, including EBROM voltage tester for mounting the devices - This combination can be mounted both horizontally and vertically, the photo is for the purpose of illustrating horizontal mounting Manufacturer of dimmer dial and frame: Busch Jäger // Manufacturer of LED dimmer and voltage tester: EBROM; A SET IDEA BY EBROM

EBROM LED DIMMER UNIVERSAL PRO 1002, suitable for dimmable LED lamps, dimmable LED drivers, incandescent lamps, HV and LV halogen lamps with electronic transformer. Freely selectable dimming principle setting (leading-edge or trailing-edge), manually switchable, simple adjustment of min. and max. brightness as an optimization option for flicker-free dimming, automatic neutral conductor detection, 2- or 3-wire connection possible, electronic short-circuit and overload protection and overheating protection with automatic reactivation, no stand-by consumption due to real on/off switch Consisting of: 3 pieces EBROM LED DIMMER TYPE 1003, 3 x Busch Jäger dimmer knob and triple frame - dimmers and knobs in the design of Busch Jäger: BalanceSi alpine white glossy EBROM flush-mounted LED dimmer UNIVERSAL ECO 1003 - trailing-edge and leading-edge dimmer. From 3 to 100 watts (e.g., also multiple 3.5 watt LEDs in one lamp) as well as for incandescent, HV and LV halogen lamps with electronic transformer from 10 to 220 W - Absolutely silent operation, no buzzing or humming, dimensions: 71 x 71 x 33 mm, 230 V~, 50 Hz nominal voltage Important: please check before purchase whether the light source and/or transformer are dimmable. We recommend light sources from well-known manufacturers. Manually switchable, simple adjustment of min. and max. brightness as an optimization option for flicker-free dimming, automatic neutral conductor detection, 2- or 3-wire connection possible. Extremely high compatibility with over 99% of all dimmable light sources available on the market Ready for installation, assembled for you by the cable professionals at EBROM, including EBROM voltage tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate the horizontal installation Manufacturer of dimmer knob and frame: Busch Jäger // Manufacturer of LED dimmer and voltage tester: EBROM; A SET IDEA BY EBROM

Blind switch insert 2000/4 US – for manual control of blinds & awnings This flush-mounted switch is ideally suited for the manual control of blind and awning motors. Thanks to the latching function, the rocker remains in the pressed position – for convenient operation without having to hold it down. Technical features: • Mounting type: Flush-mounted – suitable for standard flush-mounted boxes according to DIN 49073 • Connection type: Push-in terminal with rear conductor connection and side spring release • Mounting: Spreader claws or screws • Degree of protection: IP20 – suitable for dry indoor rooms only • Switching type: 1-pole switch, 2 buttons (Up/Down) Electrical data: • Rated voltage: 250 V • Rated current: 10 A • Maximum switching capacity: 100 V·A LEDi Note: Not suitable for automatic controls. The actuation force is approx. 2.5 – 3.5 N. ✔️ Convenient control with latching function: This blind switch stays in the pressed position – a single press is enough, and the blind moves independently to the end position ✔️ Clearly labeled rockers with Up/Down symbols: The included rockers are clearly marked and ensure intuitive operation – ideal for those who prefer classic switch logic. ✔️ Modern design in alpine white: Part of the Balance SI series – the modern, slightly curved design with soft lines adds stylish accents to any room and impresses with an elegant, unobtrusive aesthetic. ✔️ Ready-to-install set put together for you by the cable professionals at EBROM, including an EBROM phase tester for installing the "Made in Germany" device - Mounting can be done both horizontally and vertically ✔️ This set consists of: BUSCH-JAEGER frame, blind switch, rocker, and EBROM phase tester - Manufacturer of frame, switch, and rocker: BUSCH-JAEGER // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

Venetian blind push-button insert 2020/4 US – precise control with reset function This flush-mounted push-button is ideal for the precise, manual control of blinds and awnings. The rocker automatically returns to the starting position after being released – perfect for short-term operation or targeted intermediate stops. Technical features: • Mounting type: Flush-mounted – suitable for flush boxes according to DIN 49073 • Connection type: Push-in terminal with rear conductor connection and side spring release • Fastening: Claw or screw • Degree of protection: IP20 – for dry indoor areas • Circuit type: 1-pole push-button, 2 buttons (Up/Down) Electrical data: • Rated voltage: 250 V • Rated current: 10 A • Maximum switching capacity: 100 V·A LEDi Note: The blind only moves as long as the button is held down. The operating force is approx. 7.0 – 9.0 N – ideal for precise manual control. ✔️ Control with push-button function (non-latching): With this blind switch, the button returns to the starting position after being pressed. The blind moves only as long as the button is held down – ideal for precise manual control. ✔️ Ideal for living spaces with short travel distances: Perfect if you do not want to fully open/close your blinds, but rather want to stop them at specific points and fine-tune them. ✔️ Modern design in alpine white: Part of the Balance SI series – the modern, slightly curved design with soft lines adds stylish accents to any room and impresses with an elegant, unobtrusive aesthetic. ✔️ Ready-to-install kit put together for you by the cable professionals at EBROM, including an EBROM phase tester for installing the "Made in Germany" device – installation can be done horizontally or vertically ✔️ This set consists of: BUSCH JAEGER frame, blind push-button, rocker, and EBROM phase tester - Manufacturer of frame, push-button, and rocker: BUSCH JAEGER // Manufacturer of phase tester: EBROM; A SET IDEA BY EBROM

Flush-mounted dimmer suitable for a wide range of light sources, from simple incandescent bulbs to LEDs, starting from 5 watts, no interference, no flickering or similar artifacts. Trailing-edge dimmer with rotary adjustment, white with frame and cover. Full power range from 5 to 300 watts, 5 to 100 watts for LEDs. Can be used for: dimmable LED lamps, incandescent bulbs, high-voltage halogen lamps, dimmable energy-saving lamps, low-voltage halogen lamps on an electronic transformer. LED load: 5 to 100 watts, incandescent bulbs: 25 to 300 watts, electronic transformer load: 20 to 300 VA Consisting of: 3 x REV Ritter LED dimmers, 3 x Busch-Jäger dimmer knobs and a triple frame - dimmer and knobs in the design of Busch-Jäger: Balance SI alpine white glossy Flush-mounted dimmer for dimmable LED light sources: 5-100 watts, incandescent bulbs: 25-300W, LV halogen lamps on transformer: 20-300VA. Fuse: fine-wire fuse: F2AH/250V~ - Operating principle: trailing-edge With the Busch-Jäger components included in the set, you can easily convert this REV dimmer so that it blends perfectly into the existing design of your Busch-Jäger switch system at home. Ready for installation, put together for you by the cable professionals at EBROM, including an EBROM voltage tester for mounting the devices - This combination can be mounted both horizontally and vertically; the photo serves to illustrate horizontal mounting Manufacturer LED dimmer: REV RITTER, dimmer knob and frame: Busch-Jäger // Manufacturer voltage tester: EBROM; A SET IDEA BY EBROM

EBROM LED DIMMER 1001, suitable for dimmable LED lamps, dimmable LED drivers, incandescent lamps, HV and LV halogen lamps with electronic transformer. Compatible with frames and dimmer knobs from switch manufacturers such as Busch-Jaeger, Gira, Berker, Jung, and many more. Silent Technology, noiseless. Adjustable min. and max. range for flicker-free dimming, electronic overtemperature/short-circuit and overload protection with automatic reactivation. Zero stand-by consumption (true on/off switch). 5-year manufacturer warranty. Made in Germany. 100% satisfaction guarantee.

Heating emergency off switch (2-pole) with frame and rocker with red lens Consisting of: 1-gang frame studio white glossy with "Heizung" (Heating) labeling in gray - 2000/2 UK rocker control switch insert (2-pole) - rocker with red lens EMERGENCY OFF switch for heating (10A 10AX) Busch Jäger rocker switch: 2000/2 UK with lighting 2-pole (not permanent, only when ON or OFF) Color: Busch Jäger Future Linear studio white glossy Included in the delivery is an EBROM voltage tester/phase tester for mounting the switch.

BUSCH JÄGER Complete set Future studio white - UAE connection socket CAT 6A 0218/12-101 + antenna socket insert 3-hole radio/TV/SAT (**) WISI + frame and covers

The DB 53 is a 3-hole outlet for satellite reception systems for the separate connection of radio, TV receivers, and additional SAT receivers. A DC bypass is integrated into the SAT connection, enabling the transmission of the required switching voltages. The housing offers very high stability and ensures high shielding properties (Class A). Thanks to its flat design, it is space-saving, and a secure connection is guaranteed by the IEC socket/plug and F-socket. -------------------- UAE outlet insert, RJ45, Cat. 6A, shielded, 2 sockets, 8/8-pin. With angled outlet and LSA insulation displacement connectors. RJ-45 connections for networks according to Cat. 6A, Class EA (10 Gbit/s / 500 MHz). Connection labeling A and B according to TIA/EIA-568-B.2. Design according to EN 60 603-7-51:2011-01. Shielding according to DIN EN 55022, Class B. Up to 500 MHz on all wire pairs. Suitable for 10-Gigabit Ethernet. Suitable for PoE+ according to IEEE 802.3at, ≥ 1,000 mating cycles. Flexible cable feed without kinks from all sides. Housing grounding possible via 6.3 mm flat connector on the back. Suitable for mix-and-match use. Suitable for RJ 11, RJ 12, and RJ 45 plugs. For data cables with a diameter of 6-10 mm. For wires of AWG 24-22.

Heating emergency switch

TV/SAT/RADIO 3-gang in Future Linear studio white pure white glossy, with Busch-Jaeger TV/SAT/radio cover and Busch-Jaeger single frame

BUSCH JAEGER complete set/antenna socket insert radio/TV/SAT (**) WISI + 1-gang frame and cover, everything in Busch Jaeger Future Linear studio white

TAE socket (Rutenbeck TAE 3x6 NFN) Frame and cover BJ Future studio white

TAE connection socket 3x6 NFN

Flush-mounted rotary dimmer